HomeAbout UsServicesContact US
Precision Machine Works, Since 1980

Okuma LB 15 CNC Lathe

SWING ................................... 15.75"
MAX. TURNING DIAMETER ................... 10"
MAX. WORK LENGTH ........................ 9.06"
DISTANCE BETWEEN CENTERS ................ 20.47"
TURRETS ................................. 12 STATION (1)
SPINDLE DIAMETER ........................ 3.94"
BORE DIAMETER ........................... 2.20"
SPINDLE INTERNAL TAPER .................. MT NO. 6
SPINDLE SPEEDS .......................... 75 - 4,200 RPM
SPINDLE DRIVE ........................... 15 HP (10 HP CONTINUOUS)
CONTROL TYPE ............................ OSP 7000L

EQUIPPED WITH:
TAILSTOCK
8" 2-JAW KITIGAWA CHUCK
2 FOOT PEDALS
COOLANT
220/440V 62/32 AMPS@ FULL LOAD

Okuma LB 25 CNC Lathe

SWING OVER BED..................18.9"
DISTANCE BETWEEN CENTERS........26.5"
MAX. TURNING DIAMETER...........16.5"
MAX. WORK LENGTH................25.6"
TRAVELS (X) AXIS................11.82"
(Z) AXIS................26.61"
SPINDLE SPEEDS..................60 - 3500 RPM
SPEED RANGES....................2
SPINDLE NOSE....................A2-11
SPINDLE BORE....................3.15"
TURRET..........................12 ATC
QUILL TAPER.....................#5
SPINDLE DRIVE...................20/15 HP
WEIGHT APPROX...................15,000 LBS
STEADY CAPACITY .............. .1.5”-11.4”

EQUIPPED WITH
OSP 7000L CNC CONTROLS
12" CHUCK
CHIP CONVEYOR
PROGRAMMABLE TAILSTOCK


Okuma L-1420 CNC Lathe

Max Swing over Slant Bed .................................... 20.87"
Max Turning Diameter......................................... 14.17"
Max Machinable Center Distance............................... 23.62"
Cross Travel (X-Axis) Upper Slide Above Center....... 10.24"
Lower Slide Below Center ...... 5.51"
Longitudinal Travel (Z-Axis) Upper Slide.................... 25.2"
Lower Slide ................... 24.21"
Feed Range X & Y-Axis (Infinitely Variable) .................. 400 IPM
Rapid Traverse Rate X & Y Axis .............................. 590 IPM
Tool Positions (12-Upper).................................... 20 Total
Spindle Bore ................................................ 2.1"
Spindle Speed Range Main Spindle............................. 4500
Spindle Speed Range Sub-Spindle.............................. 4500
Spindle Horsepower........................................... 30 HP
Approximate Machine Dimensions............................... 189" x 78"
Approximate Machine Height................................... 79"
Approximate Machine Weight................................... 11,600LBS
STEADY CAPACITY .............. .1.5”-13”

Okuma LB 25II CNC Lathe

Max Swing over Slant Bed .................................... 19.87"
Max Turning Diameter......................................... 18.17"
Max Machinable Center Distance............................... 48.62"
Cross Travel (X-Axis) Upper Slide Above Center....... 10.24"
Lower Slide Below Center ...... 5.51"
Longitudinal Travel (Z-Axis) Upper Slide.................... 25.2"
Lower Slide ................... 24.21"
Feed Range X & Y-Axis (Infinitely Variable) .................. 400 IPM
Rapid Traverse Rate X & Y Axis .............................. 590 IPM
Tool Positions (12-Upper).................................... 20 Total
Spindle Bore ................................................ 2.1"
Spindle Speed Range Main Spindle............................. 4500
Spindle Speed Range Sub-Spindle.............................. 4500
Spindle Horsepower........................................... 40 HP
Approximate Machine Dimensions............................... 189" x 78"
Approximate Machine Height................................... 79"
Approximate Machine Weight................................... 11,600LBS
STEADY CAPACITY .............. .3”- 17.4”


Okuma LB 35 CNC Lathe

Max Swing over Slant Bed .................................... 24.87"
Max Turning Diameter......................................... 18.17"
Max Machinable Center Distance............................... 58.62"
Cross Travel (X-Axis) Upper Slide Above Center....... 10.24"
Lower Slide Below Center ...... 5.51"
Longitudinal Travel (Z-Axis) Upper Slide.................... 25.2"
Lower Slide ................... 24.21"
Feed Range X & Y-Axis (Infinitely Variable) .................. 400 IPM
Rapid Traverse Rate X & Y Axis .............................. 590 IPM
Tool Positions (12-Upper).................................... 20 Total
Spindle Bore ................................................ 2.1"
Spindle Speed Range Main Spindle............................. 4500
Spindle Speed Range Sub-Spindle.............................. 4500
Spindle Horsepower........................................... 40 HP
Approximate Machine Dimensions............................... 189" x 78"
Approximate Machine Height................................... 79"
Approximate Machine Weight................................... 11,600LBS
STEADY CAPACITY .............. .3”- 17.4”


Okuma MC-60VAE CNC Lathe

Wide Table size .................................... 20"
Long Table Size ......................................... 60"
Axis Rotary Table ............................... 4
Position index degrees .................. 360
Tool Positions (cat-50) ......................... 20


Mazak VTC-41M

Wide Table size .................................... 16"
Long Table Size ......................................... 58"
Axis Rotary Table ............................... 4
Position index degrees .................. 360
Tool Positions (cat-40) ......................... 20


CROWN L1060

Swing over bed............................... 21.65"
Swing over cross slide....................... 15.75"
Maximum turning length....................... 19.6
Maximum turning diameter..................... 10.63
X-axis....................................... 7.28
Z-axis....................................... 20.47
Spindle speed rpm............................ 4200
Spindle bore dia............................. 2.44
Spindle nose................................. JIS-A2-6
Draw tube I.D................................ 2"
Chuck size................................... 10
Turrent...................................... V12
X-axis ipm................................... 787.4
Z-axis ipm................................... 984.3
Main spindle drive motor..................... 20 hp

DAEWOO DMV 4020

Wide Table size .................................... 17"
Long Table Size ..................................... 58"
Max Table Load .................................... 1,320 LBS
X axis Travel ..................................... 40”
Y axis Travel ..................................... 20”
Z axis Travel ..................................... 20.1”
Spindle Nose to the table top Y axis Travel ........... 6-26”
Spindle Taper ..................................... CT-40
Spindle Speed ..................................... 12,000RPM
Spindle Motor ..................................... 15HP
Rapid traverse rates ..................1,417 IPM X,Y and 1,259 IPM Z
Cutting Feed Rates ..................................... 315 IPM
Tool Changer .................................... 20 SDM ATC

DAEWOO PUMA 800 CNC

Swing over bed............................... 40.5.2"
Swing over cross slide....................... 31.5"
Maximum turning length....................... 63/126”
Maximum turning diameter..................... 35.4”
X-axis....................................... 11.15”
Z-axis....................................... 26.8”
Spindle speed rpm............................ 3-750
Spindle bore dia............................. 12.6”
Spindle nose................................. A1-20
Chuck size................................... 12
X-axis ipm................................... 400
Z-axis ipm................................... 630
Main spindle drive motor..................... 60 hp

DAEWOO 300LC

Swing over bed............................... 23.05"
Swing over cross slide....................... 15.75"
Maximum turning length....................... 19.6
Maximum turning diameter..................... 50.63”
X-axis....................................... 11.28
Z-axis....................................... 52.47
Spindle speed rpm............................ 2800 RPM
Spindle bore dia............................. 4.05”
Spindle nose................................. JIS-A2-6
Draw tube I.D................................ 2"
Chuck size................................... 10
Turrent...................................... 1
X-axis ipm................................... 787.4
Z-axis ipm................................... 984.3
Main spindle drive motor..................... 35 hp


CROWN L1420

Swing over Saddle(Inches).............. 18.90
Maximum Turning Diameter(Inches)....... 14.17
Maximum Turning Length(Inches)..........25.59
Spindle Nose........................... A2-8
Hole Through Spindle(Inches)........... 3.15
Spindle Speed(Maximum RPM)............. 3500
Main Motor(HP)......................... 30
Turret Tool Positions.................. 12


DAEWOO DMV 3016

Wide Table size .................................... 17"
Long Table Size ..................................... 58"
Max Table Load .................................... 1,320 LBS
X axis Travel ..................................... 30”
Y axis Travel ..................................... 16.1”
Z axis Travel ..................................... 20.1”
Spindle Nose to the table top Y axis Travel ........... 6-26”
Spindle Taper ..................................... CT-40
Spindle Speed ..................................... 12,000RPM
Spindle Motor ..................................... 15HP
Rapid traverse rates ..................1,417 IPM X,Y and 1,259 IPM Z
Cutting Feed Rates ..................................... 315 IPM
Tool Changer .................................... 20 SDM ATC


DAEWOO PUMA 400 L CNC

Swing over bed............................... 30.5"
Swing over cross slide....................... 23.75"
Maximum turning length....................... 41”
Maximum turning diameter..................... 22”
X-axis....................................... 14.28
Z-axis....................................... 43.47
Spindle speed rpm............................ 2000 RPM
Spindle bore dia............................. 2.55”
Spindle nose................................. A2-11-15
Draw tube I.D................................ 4.62"
Chuck size................................... 15-24”
X-axis ipm................................... 630.4
Z-axis ipm................................... 790.3
Main spindle drive motor..................... 50 hp


DAEWOO PUMA 400 CNC

Swing over bed............................... 30.3"
Swing over cross slide....................... 23.25"
Maximum turning length....................... 41”
Maximum turning diameter..................... 22.4”
X-axis....................................... 14.28
Z-axis....................................... 43.47
Spindle speed rpm............................ 2000 RPM
Spindle bore dia............................. 4.05”
Spindle nose................................. A11-15
Draw tube I.D................................ 2.62"
Chuck size................................... 15
X-axis ipm................................... 630.4
Z-axis ipm................................... 790.3
Main spindle drive motor..................... 50 hp


DAEWOO PUMA 280 CNC

Swing over bed............................... 24.8"
Swing over cross slide....................... 19.75"
Maximum turning length....................... 26”
Maximum turning diameter..................... 16”
X-axis....................................... 9.25”
Z-axis....................................... 26.8”
Spindle speed rpm............................ 3500 RPM
Spindle bore dia............................. 3.38”
Spindle nose................................. A2-8
Chuck size................................... 12
X-axis ipm................................... 787.4
Z-axis ipm................................... 945.3
Main spindle drive motor..................... 30 hp


DAEWOO PUMA 300 CNC

Swing over bed............................... 23.2"
Swing over cross slide....................... 17.75"
Maximum turning length....................... 25”
Maximum turning diameter..................... 15.7”
X-axis....................................... 11.15”
Z-axis....................................... 26.8”
Spindle speed rpm............................ 3500 RPM
Spindle bore dia............................. 3.58”
Spindle nose................................. A2-8 / A2-11
Chuck size................................... 12
X-axis ipm................................... 800.4
Z-axis ipm................................... 945.3
Main spindle drive motor..................... 30/35 hp